基于外部气相沉积工艺的新型大有效面积非零色散位移光纤的设计与制备
查健江 Zha Jianjiang, 陈强 Chen Qiang, 兰兴铃 Lan Xingling, 张军 Zhang Jun, 文建湘 Wen Jianxiang
Shanghai University
阅读操作
确认中在文库中上传 PDF 后可生成中文音频讲解。
摘要与影响
Objective Transmission networks are facing explosive growth in data traffic owing to the rapid developments in data centers and cloud computing services. Optical networks with high speeds, large capacities, and high-cost performances are now in urgent demand. Telecom operators and equipment manufacturers are actively promoting the application and deployment of 400G technologies. To further develop and utilize the transmission capacity of a single fiber and approach the limit of Shannon’s theorem, the next research direction of optical transmission is prioritizing further improvements in the capacity of a single channel, compressing the transmission channel interval, and increasing the number of channels. However, increasing the number of multiplexed channels leads to a serious nonlinear effect, which is inversely proportional to the effective area of the fiber. Therefore, the transmission bandwidth and nonlinear effect of the fiber can be improved and reduced, respectively, by increasing the effective area of the fiber. Consequently, the development of next-generation G.655 and G.656 fibers, particularly for broadband transmission DWDM systems, has important practical application value. Methods In this experiment, outside vapor deposition (OVD) was used to fabricate a non-zero dispersion-shifted fiber (Fig. 3). According to the transmission principle of optical fibers, G.655 must increase the refractive index difference (RID) of the 1st core layer Δn1 to increase the waveguide dispersion and shift the zero dispersion wavelength to 1500 nm, but the increase in Δn1 leads to a decrease in the fiber core radius. However, a core radius that is extremely small results in an increase in the dispersion and nonlinear effects caused by high power density. Therefore, the profile structure selected in this experiment is a triangular core and ring structure with a central depression (Fig. 2). First, by decreasing the RID and gradually increasing the thickness of the 2nd/3rd core radii, the mold field diameter (MFD), zero-dispersion wavelength, and other parameters of the optical fiber were measured and analyzed based on this structure (Table 1). Second, in Table 3, by increasing the 1st core radius alone, the influences of the 1st core radius on the optical fiber parameters were investigated. Results and Discussions This study investigates optical fibers’ optical properties, geometric parameters, and dispersion performance by varying the refractive index profile structure and core radius (Fig. 4). The refractive index profile structure can significantly affect the cutoff wavelength, effective area, and dispersion values. In the optimized profile-type study, when the core radius of R1, R2, and R3 are approximately 2.3, 5.6, and 8.2 μm and the RID of each layer is 0.52%, 0.04%, and 0.14%, respectively, the MFD can reach 9.6 μm, and the dispersion value ranges from 1.6 to 9.5 ps/(nm·km) in the C+ L band. Furthermore, the results indicate that the core radius of the fiber has an important influence on the MFD and zero-dispersion wavelength (Table 3). The decrease in the 1st core radius is proven beneficial for enlarging the MFD, shortening the cutoff wavelength, extending the zero-dispersion wavelength, increasing the zero-dispersion slope, and lowering the dispersion (Fig. 5). The spectral loss diagram, dispersion curve, and macrobending loss diagram of the designed optical fibers were comprehensively evaluated (Fig. 6). The test results indicate that the attenuation values are 0.296 dB/km, 0.195 dB/km, and 0.203 dB/km at 1383, 1550, and 1625 nm, respectively, and the dispersion is within the standard of the G.655.D fiber. The macrobending losses at 1550 and 1625 nm are lower than 0.027 dB and 0.045 dB, respectively, demonstrating a good bending resistance. Conclusions In this study, a non-zero dispersion-shifted fiber with a triangular core and annular structure was designed and fabricated using OVD. Based on this structure, the fiber exhibited a shorter cutoff wavelength, lower attenuation, larger MFD, and lower dispersion at 1550 nm. The results show that the MFD is 72 μm2, and the dispersion value is 1.6-9.5 ps/(nm·km) in 1530-1625 nm. The attenuation at 1550, 1383, and 1625 nm excelled that of the ITU-T G.655.D standard. Overall, the proposed profile structure realizes a translation of the zero-dispersion wavelength, low macrobending loss, and large effective area, which is suitable for DWDM applications in the C+ L band. In long-distance optical fiber communication, nonlinear effects, such as FWM and XPM, can be suppressed well, and the cost of dispersion management can be reduced, which has important practical application value.
逐年被引趋势
关键指标
同类平均 = 1
同领域 · 同年份 · 同类型
Google Scholar 与 OpenAlex 的被引统计范围不同,数值存在差异属正常。
AI 辅助阅读
依据:摘要
可就本文提问;依据不足时会说明。
学术脉络
学科主题
工程Optical Network Technologies
Photonic Crystal and Fiber Optics · Glass properties and applications
参考文献 0
引用本文 1
按被引量排序,此处列出前 3 条